The OSS toolchains have matured a lot since then, with parts from Lattice being fairly well supported if you don't want to touch a vendor's tooling.
Gowin have some of the more interesting new parts which sit on a different part of the cost/feature curve. The Tang Nano boards seem fairly popular but I only have experience with far larger GW5 parts.
The newer parts from Intel/AMD have increasingly impressive hard-peripherals and internal features, but not that relevant unless you know what you want/need.
I've started to dabble in this only very recently. I have two iCEBreaker boards [0] in the mail right now that I'm excited for.
From what I understand, one of the big advantages of the up5k chip (the same chip on the webfpga and the icebreaker) is that there's an open toolchain that runs in seconds (at this chip size), which is not the case in the closed/Vivado/"typical fpga" part of the world. (feel free to correct me)
Purely in simulation this week, I had Claude (Fable) design a working Tetris out of 1400 relays - originally, this was for a Minivac web simulator that I/Fable had built [1]. Then, it compiled the relay netlist to Verilog and ran it on the simulated chip, comparing this (bezerk) port relay-for-relay against the original simulator. All matching (total llm time: less than an hour). I had it also make a viz of the netlist blinking through one simulated run [2] - sort of like visual6502.org..!
Today, I (Fable) ported tinystories [3], a very small language model to this exact same chip. It's currently "golfing" to get it to fit onto the real chip size (it's ~10% over, I'm hopeful). EDIT: it just golfed it! ~~7 tokens/sec at 12Mhz in simulation!
None of these are "use cases", but these boards seem small/cheap enough that you can do new deranged things with them, which is very very exciting to me. I see a great future.
Note, if you need a barebones CPU but want to save on gates, you can go with a serial (1-bit) CPU, e.g. SERV which only takes up 198 LUTs on ice40,[1] leaving plenty of space to do other things.
Presumably small FPGA boards, like the $47 one in the linked article
Small boards have less I/O pins than larger boards typically, and small/cheap FPGA chips on small boards are also more limited than larger, more expensive parts.
(2019). What's the latest on sub-$100 FPGAs this decade, anything significantly better than the Mojo I picked up back in 2013 to tinker with?
Depends on what you're wanting to do.
The OSS toolchains have matured a lot since then, with parts from Lattice being fairly well supported if you don't want to touch a vendor's tooling.
Gowin have some of the more interesting new parts which sit on a different part of the cost/feature curve. The Tang Nano boards seem fairly popular but I only have experience with far larger GW5 parts.
The newer parts from Intel/AMD have increasingly impressive hard-peripherals and internal features, but not that relevant unless you know what you want/need.
Outside of hello worlds, I’m always struggling to find a use case for such small boards. Any ideas?
I've started to dabble in this only very recently. I have two iCEBreaker boards [0] in the mail right now that I'm excited for.
From what I understand, one of the big advantages of the up5k chip (the same chip on the webfpga and the icebreaker) is that there's an open toolchain that runs in seconds (at this chip size), which is not the case in the closed/Vivado/"typical fpga" part of the world. (feel free to correct me)
Purely in simulation this week, I had Claude (Fable) design a working Tetris out of 1400 relays - originally, this was for a Minivac web simulator that I/Fable had built [1]. Then, it compiled the relay netlist to Verilog and ran it on the simulated chip, comparing this (bezerk) port relay-for-relay against the original simulator. All matching (total llm time: less than an hour). I had it also make a viz of the netlist blinking through one simulated run [2] - sort of like visual6502.org..!
Today, I (Fable) ported tinystories [3], a very small language model to this exact same chip. It's currently "golfing" to get it to fit onto the real chip size (it's ~10% over, I'm hopeful). EDIT: it just golfed it! ~~7 tokens/sec at 12Mhz in simulation!
None of these are "use cases", but these boards seem small/cheap enough that you can do new deranged things with them, which is very very exciting to me. I see a great future.
[0] https://1bitsquared.com/products/icebreaker
[1] https://minivac.greg.technology/tetris/
[2] https://necessary-doom-48128.ondis.co/
[3] https://arxiv.org/abs/2305.07759
Examples include:
* replacements for the C64 PLA, CIA, and potentially the SID
* Glue logic for a bread board project where it would require a lot of 74 or 4k series logic
* Translating TTL to VGA etc.
These are things people have used FPGAs for quite commonly
ICE40UP5K is large enough to synthesize a simple RISC-V CPU with some basic peripherals. It's not huge or fast, but it's capable enough.
Note, if you need a barebones CPU but want to save on gates, you can go with a serial (1-bit) CPU, e.g. SERV which only takes up 198 LUTs on ice40,[1] leaving plenty of space to do other things.
[1] https://github.com/olofk/serv
small what boards? Do esp32 boards count?
Presumably small FPGA boards, like the $47 one in the linked article
Small boards have less I/O pins than larger boards typically, and small/cheap FPGA chips on small boards are also more limited than larger, more expensive parts.
Edit: precise price.
Jailbreaking consoles
https://a.co/d/05f9gq9A
Direct link: https://www.amazon.com/dp/B0D9Q8VSSM
“KooingTech 150MHZ Machine Pulse Chip Mode Chip ACE V3 for X360 Slim”
Why do the synthesis in the cloud, and not locally?
+1. Especially given that it can even run in the browser - https://yowasp.org/
I guess it's for people who only have a smartphone. Or a potato that is ok for browsing, but not for FPGA synthesis.
My first thought: yet another web browsers standard.