My favorite car was a 92 BMW 325IS coupe, standard. It was a simple driving machine. It drove well. It performed when asked. It had room for four, or three plus skiis with half the rear seat folded down. And BMW took a strong stance against drinking and driving: zero cup holders.
I miss that car. I would buy one again in a heartbeat if BMW still made them.
My E36 was fantastic as well. Automatic climate control, heated motorized mirrors, heated monkey pissers, heated power-adjusted leather seats, power windows, power sunroof, dash lights that fluidly adjusted to ambient conditions, two throttle bodies (in series -- one for the loud pedal, one for the ASC+T), and a single-DIN radio that was dead-nuts simple to upgrade properly whilst leaving the rest of the factory system (and its 10 channels of amplification) intact.
That's a pretty long list of things for a simple driving machine.
But anyway:
It came with two cup holders in the center console, BMW part 51168205367. There were two more cup holders in the middle armrest for the rear seat. Two additional cup holders were also available, which fit under the top of the glove box -- BMW part 51168184470.
I loved that car and it was brilliant to drive, but it did not represent a "strong stance" about drinking and driving.
It was a rather complex machine that came fitted with plenty of cup holders. :)
Sounds like you had the north america version. Mine was built in Europe, first sold in canada. It had to be dealer-modified for daytime running lights before being first sold (headlight switch "off" was turned into another on.)
I found an add-on cup holder (similar to one I had for my NSX which had none from the factory) that clips behind the inner center console panel and the cup sits on (or near, depending on diameter) the floor. Unfortunately it is expensive for being a 3D printed part that needs better QC (had to sand the changeable cup part) (the NSX one was aluminum) but it works very well.
A better design would be to have a smaller diameter clip-in piece so you can size down when you have a smaller item.
My favorite car was a 92 BMW 325IS coupe, standard. It was a simple driving machine. It drove well. It performed when asked. It had room for four, or three plus skiis with half the rear seat folded down. And BMW took a strong stance against drinking and driving: zero cup holders.
I miss that car. I would buy one again in a heartbeat if BMW still made them.
My E36 was fantastic as well. Automatic climate control, heated motorized mirrors, heated monkey pissers, heated power-adjusted leather seats, power windows, power sunroof, dash lights that fluidly adjusted to ambient conditions, two throttle bodies (in series -- one for the loud pedal, one for the ASC+T), and a single-DIN radio that was dead-nuts simple to upgrade properly whilst leaving the rest of the factory system (and its 10 channels of amplification) intact.
That's a pretty long list of things for a simple driving machine.
But anyway:
It came with two cup holders in the center console, BMW part 51168205367. There were two more cup holders in the middle armrest for the rear seat. Two additional cup holders were also available, which fit under the top of the glove box -- BMW part 51168184470.
I loved that car and it was brilliant to drive, but it did not represent a "strong stance" about drinking and driving.
It was a rather complex machine that came fitted with plenty of cup holders. :)
Sounds like you had the north america version. Mine was built in Europe, first sold in canada. It had to be dealer-modified for daytime running lights before being first sold (headlight switch "off" was turned into another on.)
I've had to give up drinking trenta-sized Starbucks entirely.
I found an add-on cup holder (similar to one I had for my NSX which had none from the factory) that clips behind the inner center console panel and the cup sits on (or near, depending on diameter) the floor. Unfortunately it is expensive for being a 3D printed part that needs better QC (had to sand the changeable cup part) (the NSX one was aluminum) but it works very well.
A better design would be to have a smaller diameter clip-in piece so you can size down when you have a smaller item.
a good idea anyway